Milwaukee

The light is necessary for the development of the plants.

In fact, it is necessary a sufficient contribution of light in order to favor the photosynthesis and the closing of the plants. The supplement of light by means of lamps electrical workers is the method simpler and economic in order to bring the necessary light to the plants.

MW700 is a portable Lux meter designed to perform light measurements. It is supplied with a light sensor connected to the meter that measures from 0 to 50000 Lux. Average indoor lighting ranges from 100 to 1000 Lux and average outdoor sun lights about 50000 Lux. Lux is a unit that indicates the density of light that falls on a surface.

The MW700-WP is a portable Lux meter designed to perform light measurements. The instrument is supplied in a hard carrying case complete with a light sensor connected to the meter that measures from 0 to 50000 Lux. The light sensor is waterproof, suitable to verify the light intensity also at the bottom of your aquarium. The accuracy is ±6% of reading (full scale). The MW700-WP works with a 9V alkaline battery. Automatic shut-off after 10 minutes saves battery and extends Lux meter life.

pH 600 Specifications

- Range 0.0 - 14.0

- pH Resolution 0.1

- pH Accuracy ± 0.1 pH

- Calibration 1 Point (7.0) - Manual

- Environment 32 - 122F

- Display LED

- Battery Life 700 hours of use

- Battery Type 1.5v Button - 3 Included

Milwaukee's economical testers are easy-to-use and low cost instruments to measure quick and reliable pH, EC or TDS values.

Measuring electrical conductivity is the best way of checking the amount of salt or dissolved solids (TDS) in water. Milwaukee provides you with a range of pocket testers that will allow you to measure from very low to very high conductivity solutions. All EC/TDS testers compensate for the temperature variance automatically.

The CD611 is a Conductivity tester specifically designed for water analysis. The calibration procedure is very simple and fast. This tester has automatic temperature compensation, 100 µS/cm resolution and a range of 0 to 20000 µS/cm. CD611 is supplied complete with protective cap, calibration screwdriver, batteries and instructions.

Milwaukee C65 / C66 is a waterproof EC tester, specially designed for hydroponics and agricultural markets, with automatic temperature compensation and manual calibration with 1 point.

The EC tester has a range of 0.00 to 10.00 mS / cm as well as an optional electrode option and is supplied in a battery pack, calibration solution (M10031) and a calibration screwdriver. The modular design allows easy replacement of the electrode and batteries.

Specifications:

• range: from 00 to 10.00 mS / cm
• resolution: 0.01 mS / cm
• accuracy: ± 2%;
• Calibration: automatic, single point
• automatic temperature compensation with β = 2% / ° C
• Operating conditions: -5 to 50 ° C / 32 to 122 ° F ;, humidity up to 100%
• batteries: 3 x 1.5V (included)
• Battery life: approx. 250 hours of continuous use
• dimensions: 165 x 30 x 30 mm

CALIBRATION:

• Frequent calibration is recommended for maximum measurement accuracy.
• Immerse the tester electrode in a glass of tap water
• Immerse the probe in a suitable calibration solution: 1413 mS / cm.
• Open the top cover of the tester and, using the screwdriver included in the kit, turn until 1.41 appears on the display.

Тhese tools are widely used.

With an IP65 waterproof housing and replaceable probe, the tester is suitable for many applications, such as a measuring instrument from wastewater treatment to agriculture. The modular design allows easy replacement of probe and battery.

PH54 is a waterproof pH tester with 2 points for manual calibration, ± 0.1 pH accuracy and a range from 0.0 to 14.00 pH.

Specifications:

• Measuring range: 0.0 - 14 pH
• Resolution: 0.1 pH
• Accuracy: + -0.1 pH
• Environment: 0 to 50 ° C; max. RH 100%
• Calibration: manually at 2 points using trimmers
• Electrode: MA73600 (replaceable)
• Power supply: 3x 1.5V (included)
• Battery life:> 1500 hours of continuous use
• Dimensions: 165 x 30 x 30 mm

Calibration:

- Immerse the switched off tester in a glass of tap water

- Move it while it is still switched off in buffer solution 7.0

- Unscrew the cap and use the supplied screwdriver to set the display to 7.0

- Dip the tester briefly in the glass of tap water and shake gently

- Immediately move the tester to buffer solution 4.0

- Use the supplied screwdriver to set the display to 4.0

- your tester is calibrated!

This new waterproof Pocket-size EC/TDS/Temp Meter include features such as a replaceable probe, temperature in °C or °F, automatic temperature compensation with adjustable ß, battery level indicator, stability indicator, automatic shut-off and automatic calibration all in a floating, waterproof casing.

EC60 shows on the dual-level LCD the EC (20.00 mS/cm) or TDS (10.00 ppt) value. It also displays the temperature from 0.0 to 60.0°C (or 32.0 to 140.0°F) on the secondary level at the same time.

INSTRUCTIONS FOR CALIBRATION AND OPERATION OF THE TESTER, YOU CAN FIND HERE

PH buffer solution  4,01 20 ml

- pH-4.01 buffer solution for calibration of electronic pH meters

- content: 20ml

- calibration-table on the packaging

 20 ml pH 7.01

 

-liquid pH 7.01 to calibrate electronic pH meters

-content: 20ml

- calibration-table on the packaging

EC buffer solution 20 ml 1.413

- solution EC  1,413 for the calibration of electronic meters EC

-content: 20ml

- calibration table on the packaging

EC buffer solution 20 ml 12880 µS/cm 

- solution EC 12880 µS/cm for the calibration of electronic meters EC-

- content: 20ml

- calibration-table on the packaging